What Kind Of Cable To Upload Data On Edge Programmer

USB Cable Drivers

FTDI / Prolific / SiLabs / WCH

Microsoft (tm) Drivers

May 2013, 2015, 2019
Rev 7/2020
John K3NXU Jim KC9HI

Important Notes - Read First

Your programming cablevision Must have the correct driver installed to interface with your estimator. Some critical notes:
- Not all cables load the correct driver automatically.
- Not all provided CDs come with the correct drivers.
- Cablevision drivers are not interchangeable

Past using Windows Device Managing director, you should easily exist able to determine which bit is in your programming cablevision.

FTDI chipsets
Cables with FTDI chipset (FT232R) volition automatically download the correct commuter when inserted into the USB port.

WCH chipset
Many Baofeng and generic programming cables are aircraft with the WCH chipset (CH340/341). The driver should too download automatically. If not, the driver and procedure can exist institute at this Link.

SiLabs chipset
Drivers for the Silicon Labs chipset (CP210x) should also download automatically. If not the driver can be plant at this Link.

Prolific Chipset
Well-nigh every programming cable that is detected by Windows as having a Prolific chip was manufactured with an unauthorized or cloned copy of the Prolific PL2303HXA flake. The latest driver installed past Windows (Vista, 7, 8.1 and x) is not uniform with these fries. The terminal compatible Prolific commuter was v3.iii.2.105 [27/x/2008]. Windows may try to automatically load the Prolific commuter three.6.xx.xxx when inserting your cablevision. When opening Device Manager, the Yellow Circumspection Triangle may non appear, however, when the cablevision is inserted into the radio, the transmitter will turn on. This should non occur. It was done to prevent use of the cloned chip. More than detail tin be institute Here.
If this occurs, yous Must backdate your driver to 3.2.0.0
(Become directly to Install Drivers)

Windows Device Manager

If Windows does non automatically load the proper driver, a caution message will appear in Device Director. Case shown here is for a WCH340 chip.

Note: If y'all recently upgraded to Win10 and the V3.2.0.0 driver was previously installed on your computer, you will only demand to select it once more. See step vii in the "Installing the Backdated Prolific PL-3203 Driver" section below.

Prolific Driver 3.2.0.0 recommended for Vista, Win7/8/10
three.two.0.0 exe 3.2.0.0 naught (32/64 chip)
- XP:
If you are using Win XP, the Prolific driver 2.0.2.1 will run with no issues. This driver for Win XP can be constitute here: 2.0.2.1.zip

- MacOS
The recommended Drivers and Info can be found at the lesser of this folio.

FAQs and Fault Messages

Determine what Cable I take

Installing the proper Commuter 3.2.0.0

MacOS - Drivers and Info Below YouTube Video describing the Procedure

What UART fleck does my cable have ?
Exercise I Accept the Proper Windows driver ?

one) Insert your USB Programming Cablevision.

ii)

Launch Device Managing director.

[ Start | Right-click Estimator | Select Properties | Device Manager ]

Failure

3) Select: Ports (COM & LPT)

Failure

It is recommended that the driver be backdated to 3.2.0.0 if:

A - A yellow warning triangle appears under 'Ports' or 'Other Devices'
B - The Prolific 'Phased Out' bulletin appears

Also, if you insert your programming cable into your radio, and the transmitter turns on, you will demand to load the backdated driver 3.two.0.0 as described beneath.

Note:
Your software will ask for this Com Port number later.
If you change USB ports, the Com Port number will also change.

Note:
If Device Managing director does NOT say "Prolific", Cease hither .

There are several USB Driver chipset manufactures.
SiLabs, FTDI, WCH
The 'Prolific' drivers will not piece of work with these chipsets.

Installing the Backdated Prolific PL-2303 Driver iii.2.0.0

System Requires 32/64 bit Windows Vista / vii / 8 / 10

i) Create a piece of work folder (New Folder) on your PC.

ii) Download the Prolific 3.2.0.0 driver file and relieve it to the piece of work folder.

iii) Remove the USB programming cablevision from your PC.

4) Double-click the file that was saved into the work folder and follow the prompts until information technology is completely installed.

5) Plug the USB programming cable into the USB port of your PC.
You lot should see a airship popup that says "Installing device commuter software"

A few seconds afterward you will get a balloon popup that says
"Device driver software was not successfully installed"

6) Launch Device Manager.

[ Start | Right-click Figurer | Properties | Device Manager ]

You volition see i of the post-obit errors in Device Manager.

In 'Other Devices' the 'USB-Serial Controller' is proceeded by a Yellow alarm.

OR

In 'Ports (COM & LPT)' the 'Prolific USB-to-Series Comm Port (COMx)' will appear.

seven) Right-click on the entry with the fault to open up a window and select
"Update driver software..."

8) At the first Update Driver Software prompt, select
"Browse my calculator for driver software".

ix) At the second Update Driver Software prompt, select
"Let me option from a list of device drivers on my computer"

10) At the third Update Driver Software prompt, scroll downward and select
"Ports (COM & LPT)".

11) At the quaternary Update Commuter Software prompt, select
"Prolific USB-to-Series Comm Port Version: 3.2.0.0 [7/31/2007]".

Y'all should get a prompt saying that the commuter was installed successfully.
Yous should now see a properly installed Prolific driver in Device Manger.

You lot can cheque that the correct version is installed by double-clicking on the Prolific entry in device manager and selecting the Driver tab.

The driver version shown should be v3.two.0.0

12) Remove the USB programming cable from your PC and then plug the USB programming cablevision back in.

thirteen) (Optional) Reboot your calculator.

FAQ 1
Q: My programming cable is not existence recognized.
(Handheld radios using 2 pin plugs)

a) "Radio did Not Respond" or
"Radio did Non Ack Programming Mode" message appears.
This is a very common problem.
Slightly offset audio jacks could exist the trouble.

Brand sure the connector is

snapped in all the style .
Some cables require a really hard button to snap in that last one/16 inch.

One indication is that the transmitter may be keyed.
A slight trimming of the cablevision'due south plug side and edge may be required.

This message appears if the radio is not turned ON while downloading.

b) "Fault has Occurred, Could not open Com Port x"
Each USB slot is connected to a separate com port to avoid disharmonize.
Changing your USB slot will modify the COM port number.

c) "Run-fourth dimension mistake 8020: Error reading from comm device."
Error occurs if Prolific driver version is higher than v3.two.0.0
Yous must Downgrade to v3.2.0.0

FAQ 2
Q: Why doesn't my new driver work whatsoever longer?

A: The driver does not follow the cable. If the cable is moved to a different USB slot, Windows volition at present load the newest driver to that port. (not 3.two.0.0)

When this occurs, you will need to either load driver 3.2.0.0 to the new USB slot, or plug the cable back into its original USB slot.

You can check the commuter loaded using the procedure above. Cablevision

FAQ 3
Q: Is there a quick mode to detect my cable's com port number?

A: Aye. Run: Find Com Port (Windows)

FAQ 4
Q: Afterward changing the com port number of my USB cable in Device Manager, my software reported:
"An fault has occurred - could not open port com[n]: (2, 'CreateFile', 'The arrangement cannot notice the file specified.')"

A: After making this change, y'all must unplug and reinsert your USB programming cable for the com port number alter to be effective.

Note 1: If you are having com port / driver issues, please note this is NOT caused past your software. It's strictly betwixt the PC driver and the cable.

Annotation 2: Each USB slot is connected to a dissever com port to avoid conflict.
Plugging your cable into a dissimilar USB slot will modify the com port number and will attempt to load the Newest Driver. Make sure the driver loaded for the new com port is iii.ii.0.0
FAQ 5
Q: How do I prevent Windows 7 from automatically installing new drivers?

A: This solution can be found at this Microsoft link .
Note: (This does not apply to Windows 10) .

Build your own Programming Cable

Here'southward a project to catechumen your current cable to one
using a Silicon Labs CP2012 UART bit.
No driver errors at all.
Build Your Own Cablevision

My thanks to Jim, KC9HI for his hours of
testing and his input to this folio.

73 John 'Miklor' K3NXU

Source: https://www.miklor.com/COM/UV_Drivers.php

Posted by: chungandutimmose1944.blogspot.com